Request a quote for this configuration
Chat on WhatsApp +86 13068616914
What makes the R730xd worth sourcing separately
The R730xd is the 2U member of the Dell PowerEdge 13th-generation family that was built for density rather than for maximum drive count per front bay. In the 24-bay SFF layout it takes 24 x 2.5-inch drives; in the 12-bay LFF layout it takes 12 x 3.5-inch drives. That is the practical reason buyers search for this model on its own: the drive layout, the backplane and the controller are a matched set, and the part number decides which set you get.
Because the configuration is confirmed per part number rather than fixed per model, a quote always states the chassis, the backplane, the RAID controller, the CPU and memory fitted, and the drive caddies included. There is no public price list and no blanket stock claim on this page – the quote is the answer, and it is issued per part number.
Used Dell PowerEdge R730xd configurations we quote
The table below lists the chassis layouts the R730xd family is built around. Availability is confirmed per part number.
| Model | Chassis and drive layout | Fitting that changes the decision | Availability |
|---|---|---|---|
| Dell PowerEdge R730xd, 24-bay SFF | 2U rack, 24 x 2.5-inch SFF bays, dual-socket Xeon E5-2600 generation | Backplane and controller must match the 24-bay SFF layout; a 12-bay controller does not drive 24 bays | Confirmed per part number |
| Dell PowerEdge R730xd, 12-bay LFF | 2U rack, 12 x 3.5-inch LFF bays, dual-socket Xeon E5-2600 generation | Confirm LFF caddy and backplane revision, and that the controller you hold supports 12 LFF drives | Confirmed per part number |
| Dell PowerEdge R730xd, 8-bay SFF | 2U rack, 8 x 2.5-inch SFF bays, dual-socket Xeon E5-2600 generation | Drive layout is close to the R730; check the backplane revision before treating it as an R730 equivalent | Confirmed per part number |
| Dell PowerEdge R730, 2U | 2U rack, 8 x 2.5-inch SFF or 12 x 3.5-inch LFF bays – the comparison point | Fewer bays than the 24-bay R730xd, which is the reason most buyers step up to the R730xd | Confirmed per part number |
Availability: every R730xd configuration above is quoted per part number. Availability is confirmed per part number when you request a quote, and pricing is quoted for your quantity and destination – there is no public price list and no standing stock claim on this page.
R730xd vs R730: what actually changes
Three things change when you move from the R730 to the R730xd, and two things do not. It is worth being precise about this because most listings blur the two models together.
- Drive bays change. The R730xd raises the SFF count to 24 in the SFF layout. The R730 stays at 8 SFF, or 12 LFF. This is the single largest practical difference and the reason the R730xd is a separate buying decision rather than a substitute.
- Backplane and controller become a matched pair. The 24-bay SFF R730xd needs a backplane and controller that drive 24 bays. Moving a controller across from an 8-bay chassis is not a drop-in swap, so the part number has to be checked against the backplane before anything else is agreed.
- Thermal and power design follow the drive count. A 24-bay SFF front carries more drives in the same 2U envelope than an 8-bay LFF chassis does. Airflow path, fan cage and power supply loadout are all affected, so we record fan behaviour and power-supply condition per unit on this platform.
- The CPU and memory generation does not change. Both platforms sit in the same 13th-generation Dell PowerEdge family and take the same 2-socket Xeon E5-2600 generation CPUs and DDR4 memory. A CPU or memory configuration that fits an R730 generally fits an R730xd.
- The management stack does not change. iDRAC and the lifecycle controller work the same way on both, so an environment that already manages R730s manages R730xds with no tooling change.
For the wider PowerEdge range, the R640, R650 and R750xa sit alongside these models in our used server line – see Used Dell PowerEdge R730xd servers for the full PowerEdge list and Used Dell PowerEdge R730xd servers in our barebones category for chassis-only builds.
How a used R730xd is tested before it is quoted
Every unit is cleaned, re-flashed and bench-tested on our own test line, then run through a seven-point check:
- Chassis, backplane and front panel inspection, with the drive bay count confirmed against the part number
- Firmware level, BIOS and iDRAC revision recorded per unit
- Full power-on and memory training pass, including a documented burn-in under sustained load
- RAID controller and storage backplane detection, with the controller model and cache state recorded
- Fan behaviour under load and power-supply condition tested, including redundancy where the unit carries it
- Error log cleared and re-checked after the test run
- Full power-on and memory training pass, and a POST result recorded before the unit is listed
Request a Dell PowerEdge R730xd quote
Send the part number, the drive layout you need and the quantity. We confirm the configuration and availability against that part number, and quote it for your destination. WhatsApp +86 13068616914, or browse zhongxindata.hk for the rest of the range.
+86 13068616914
Frequently Asked Questions
Is a used Dell PowerEdge R730xd worth buying compared with the R730?
Yes, when you need the drive density the R730xd was built for. The R730xd carries up to 24 SFF bays or 12 LFF bays in the same 2U chassis, while the R730 tops out at 8 SFF or 12 LFF. Everything else in the platform family is close enough that a used R730xd is usually the cheaper route to 24-bay density. The trade-off is drive backplane and controller matching, which you confirm per part number.
What should I confirm before ordering a used R730xd?
Send the part number and we confirm the chassis, backplane type, controller, CPU and memory configuration, drive fittings, fan cage and power supply loadout against it before you commit. Every unit is bench-tested on our own test line, and the exact configuration of each unit is stated in the quote.
Does a used R730xd include CPUs and memory?
It depends on the part number, so we quote what is actually fitted. A barebone chassis arrives without CPUs, memory and drives, and a configured unit arrives with the CPU and memory listed against it. Both are quoted per part number and priced for the configuration you send us.
Request a quote for this configuration